How to connect a projector with a motion detector?

This self-lighting luminaire is wall-mounted on a front wall, fence or gate pillar, for example. Its directional motion detector turns on the halogen lamp as soon as it spots the heat of a moving body in its area of ​​coverage.
1 Understanding the different parts of the projector

The luminaire consists of three main organs, from top to bottom:

The waterproof body with reflector, lampholders and protective glass.

The electrical connection box.

The motion detector with three adjustment buttons.

The assembly clings to a support (or bracket) which is fixed to the wall, in three points, by pegging and screwing.

 2 Set the location

For optimum efficiency, place the projector at a height between 2 and 3 m from the floor. At this height, the detector covers an angle of 120 °. The minimum / maximum detection distance is 1 to 10 m

Check that there are no obstacles in the coverage area

To avoid nuisance tripping, avoid pointing the detector towards a source of heat or light, towards a surface reflective or likely to experience rapid changes in temperature (pool water, windows in a greenhouse or veranda.

1. resent the media in the desired location.
2. Make sure to level it well, and mark with a pencil its fixing points through its perforations.
3. Drill the masonry with a hammer drill or drill according to its hardness.
4. Insert into the holes dowels of suitable diameter and screw the support.
5.  
6. Connect the power cable
   Turn off power at the main circuit breaker before making electrical connections
   
   
   
   
   The circuit
   • The projector is powered by a 1.5mm2 three-conductor cable (Ph, N and T).
     For outdoor connections, use a standard HO5RN-F3G1 type cable.
   • The power supply can be done at the exit of wall (circuit recessed under corrugated sheath) or in apparent under rigid tube.
   • We advise you to mount on the route a selective switch that allows, at choice, a manual or automatic use of detection.
   
   
    
7. The circuit
   
   
   The projector is powered by a 1.5mm2 three-conductor cable (Ph, N and T).
   For outdoor connections, use a standard HO5RN-F3G1 type cable.
   
   
   The power supply can be done at the exit of wall (circuit recessed under corrugated sheath) or in apparent under rigid tube.
   
   
   We advise you to mount on the route a selective switch that allows, at choice, a manual or automatic use of detection.
   
   
    

The connection of the projector

It is easier to connect before setting up the projector.

Unscrew the control box plate to access the terminal strip. Be careful not to lose washers and seals.

The bar has four connection terminals. Only three concern you: they correspond to the phase, the neutral and the earth.

Strip the strands of the power cable to 6 mm.

Unscrew the cable gland and cable clamp from the housing to route the cable. Tighten each wire into the appropriate terminal: red (phase), blue (neutral), green-yellow (earth).

Screw in the cable clamp and cable gland and close the housing.

Position the projector and the halogen lamp

Fix the projector on its support using the two side screws.

After making sure that it is hooked, unscrew the glass cover and carefully remove it.

Setting up the halogen lamp requires a lot of care. Use a clean, dry cloth (or glove) to handle it.

First, put one end of the lamp on one of the two sockets.

Apply slight pressure to clip it and insert the other end into the second socket.

Tips :

If, by mistake, your fingers have touched the glass of the lamp, gently clean it with a cloth soaked in 90 ° alcohol

Turn on the power and turn on the switch. 

To enable you to define the coverage area, the detector goes into test mode. You have 4 minutes to adjust the sweep by orienting the device accordingly. 

Move slowly around the area. Each time you enter the field, the detector triggers the light and turns off after 4 seconds. 

Next, determine the radius of action by rotating the detector up and down. The higher it is, the greater the detection distance and the less sensitive the device is to the movement of pets. 

Now adjust the light sensitivity. Turn the corresponding knob to select the threshold from which the light will go off.

It remains to set the timer (duration of ignition) in automatic mode, according to the range predefined by the manufacturer: for example, from 10 seconds to 10 minutes.